Stanley 55 plane parts. Stanley No. 45 and No. 55 Combination Plane 2019-01-21

Stanley 55 plane parts Rating: 4,3/10 1423 reviews

The Stanley No. 55: King of Combination Planes

stanley 55 plane parts

It's very easy to smack this piece on the end of the board, which then causes the piece to move backward at the bottom, and forward at the top. If it isn't, the plane will bind - the cutter will tend to draw the fence tighter and tighter to the edge, the deeper it cuts - or the plane will ride off the board - the cutter pushes the fence away from the board's edge, the deeper it cuts. This piece sits in a shallow track, which can break out over time. . Since the fence is supported by curved arms, this feature allows the plane to be worked farther from the edge than it normally would be. State of Washington residents please add 8.


Next

Stanley No. 55 parts/restoration

stanley 55 plane parts

The four boxes illustrated here show the 52 cutters that were offered with the plane when it made its debut. The earlier models can be found with the March 10, 1896 patent date embossed in the main casting of the tool. Down in Australia this chunk of metal has been used as a doorstop no lie. A long threaded rod accomplishes this. The procedure to make a core box is to layout the diameter of the semicircle, and then rough the waste out with gouges, a router non-electrical, of course , whatever, with great care given to the area of the endpoints of the semicircle. The hollow and round attachments work better than the cutters on the No.

Next

STANLEY NO. 55 plane for PARTS

stanley 55 plane parts

It goes a bit further by facilitating cutters that require irregular bearing points across their width. Farnsworth Below you will find a tool for Stanley plane identification, specifically dating Stanley planes and identifying the type of your Stanley Bailey woodworking bench hand planes. When using the plane, take care to secure this part in place tightly and don't let it whack the end of the board. The turnbuckle can place a lot of pressure on the extensions when they are overtightened causing the extensions to crack. And very much so, at that, as it seems that Stanley wanted to deplete the free world's nickel resources, with this plane as proof.

Next

The Stanley No. 55: King of Combination Planes

stanley 55 plane parts

The plane came packed in many different containers. As you push the 55 forward, be certain to hold it firmly against the edge of the work- piece. Stanley Plane Identification: How to Identify Antique Stanley Bailey Hand Plane Age and Type? Note the camera angle grossly exaggerates the exposure of the cutter relative to the runner. And while on the subject of the cutter, this plane's cutter is sharpened with two bevels so that they form a V at the leading edge. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. Each box has a label to illustrate each cutter within the box. I have already been on eBay and found quite a few parts but feel as though some are a little over priced.

Next

Unique Tips For Hand Tools : The Stanley 55 socialsamba.com Than A Paperweight

stanley 55 plane parts

The turnbuckle is first turned to force the rods outward, and the nuts are then tightened, often with the end of screwdriver or similar tool, against the turnbuckle. Some woodworkers complain that the 55 is a booby trap, enticing them with visions of complex moldings easily cut only to frustrate their every attempt to use it. There is a cast iron turnbuckle that keeps the extensions rigid by forcing the extensions outward. This L-shaped part has a lot of stress put on it by the center bottom skate , if the workman isn't careful when starting the plane. Since the rosewood face can pivot, catastrophic in the planing sense results can occur if particular attention is not paid during set-up. This forum is for all the woodturners out there.

Next

The Superior Works

stanley 55 plane parts

It also suffers the same deficiency that the does regarding stock selection - the wood must be even-grained to minimize tearout, since there is no mouth, in the true sense of the word, on this plane. If they aren't, you can face them up with a smoothing plane provided there is enough rosewood left before you hit the heads of the fastening screws. The earliest models have beech while the later have rosewood for their wooden parts. Wooden molding planes are self-regulating; i. The plane is pushed and held in the hands with a conventional bench plane style knob and tote. The plane, like many of the products Stanley made during the era, is nickel plated.

Next

STANLEY NO. 55 plane for PARTS

stanley 55 plane parts

It would be too easy to say that screw is where the chain is fastened to the plane - the same chain that has a shackle on the other end through which the owner's ankle is fastened, but that wouldn't be true. Besides the 55 standard cutters, Stanley made an additional 41 special cutters with more sizes of quarter rounds,hollows, ogees and beading cutters. Any product claim about a service or product should be verified with the manufacturer. This often means using more than one depth stop, fence, or skate. Dorn's Patent Plane Coming Soon! My perception of condition is conservative and hopefully you will be pleased with receiving an item that will be better than your expectations. The rosewood face must be perfectly parallel to the side of the cutter.

Next

The Superior Works

stanley 55 plane parts

Small accessories, such as the screws, cam, rods, and rear depth stop are interchangeable between the planes. It was later offered with 55 cutters, but this was long after the plane was out on the market. Production of this plane ceased in 1962. It is a mistake to guide the 55 by holding the rosewood handles attached to the fences. A proper lever cap is nickel plated and has its sides bevelled along its length and the bearing surface at its bottom isn't straight across but is more a cross between a U and V. Two skates, one at each side of the bead are positioned; one skate, on the main stock is fixed, and the other, part of the sliding section, is secured to the arms. Lori Goucher , 480 Myrtle St.

Next

The Superior Works

stanley 55 plane parts

As far as I know, the No. Gripping the tool there puts your hands too high above the cutting surface and too far from the main body of the plane to provide good control of the cut. The left side of the sole has the shallow groove milled along the vertex, which is opposite how the 's sole is milled. These are not marked with a diamond in the illustration The No. The heel top of the cutter sticks up above the casting, right where it can rip unsuspecting flesh to a bloody mess, so many of the planes have the cutter reshaped to minimize bloodletting during use.


Next

The Superior Works

stanley 55 plane parts

Justus Traut and Edmund Schade devised a torture that knew no bounds betwixt Gods and mortals. It, in turn, attaches to part 50, and allows the the rosewood strip to pivot. Put simply, it's a temperamental monster that requires much fussing with in order for it to work well. Traut worked with the Stanley Company from 1870 to1908. Have you had to compromise your project. Check that there is no chipping about the plane's mouth.

Next